ORTUR Laser Master2 Laser Engraver 5.5W Pro S2-LU2-4-SF DIY Engraving Machine US

  

ORTUR 24V Laser Engraver Cutter 2 Pro-S2-LF Laser Machine 5.5W Output Power DIY. [Product advantage] Ortur Laser 1.8 firmware is optimized the motion algorithm and increases the maximum motion speed from 4000mm/min to 10000mm/mm, the focal point is only 0.170.25mm.

So it can cut through 4mm plywood and 10mm pine board at a time. At the same time, the laser cutter comes with an air assist nozzle, use with our air pump could support a higher speed and cut better.

[Safety protection] Laser Master newly upgraded 5 Safety protection. When the engraving machine is displaced or tilted, it will automatically stop the laser; 2. When the engraving machine or computer crashes, the laser will stop working immediately. The engraving machine is turned on, but there is no movement for a long time, the laser will be turned off automatically. Flame Detector + Buzzer Alarm 5.

Emergency stop switch for an emergency. The laser engraving machine is equipped with the latest OLM-PRO-V10 motherboard, It could preprocess 32 instructions, support baud rate as high as 921600 the engraving accuracy is higher, and the speed is faster.

The circuit system with 24V voltage is upgraded, the current is lower, and the system is safer. Update Ortur Laser 1.8 firmware, which is the most advanced laser engraving machine firmware at present. Support Ortur offline control screen. [Sturdy and Easy Installation Structural Design] Pre-assembled parts, just need 10 - 20 minutes to install the laser machine. Aluminum profile frame + structured cabling, solid structure, smooth operation. Synchronizing shaft mechanical structure, avoid out-sync on two Y rails, during full speed engraving. LU2-4-LF is good at engraving and better at cutting, and could support a higher speed. It is not that the smaller the light spot, the better the effect when engraving photos. You may need to increase the laser spot to get a better picture effect.

The competitors may falsely promote the power of similar laser modules as 40W, or even 60W, please take care. It has a longer Focal Length, so it has a longer Depth of Field, but a bigger Focal Spot.

Extra Accessories: Safety Glasses, 10PCS Metal Business Cards, 2PCS Color Paper, 4PCS Pet ID Tags. This laser engraver supports PWM mode.

Pre-assembled parts, just need 10 - 20 minutes to install the machine. 400 x 400 mm large engraving area. Aluminum profile frame + structured cabling, solid structure, smooth operation, attractive appearance. Flame Detector & Buzzer Alarm. When the laser engraver detects flame, it will automatically stop and beep. There is a switch for emergency stop. Once there is a emergency in the process of engraving, you can press the emergency stop switch to stop engraving. There is a G-sensor on the motherboard. Once the laser engraver detects unauthorized movement, the laser beam will stop.

If your computer system halted or USB cable disconnected and then the laser engraver stops moving, the laser beam will stop to prevent fire. Exposure Duration Detection and Limitation. Once the laser cutter is under control but the users forget to operate it, the motor will stopped working. And then the laser beam will stopped after a while to prevent fire. Once the laser engraver disconnect to the power, it would cut the power to the laser module.

Adopts newly laser protective cover, the ORTUR laser engraving machine can filter out 98% UV light to perfectly protect your eyes to reduce the cost of your goggles and the inconvenience of wearing goggles. Specialized Motherboard with 32Bits MCU. It could pre-process 32 instructions, support baud rate as high as 921600, which is much more powerful!

The Most Advanced 32Bits Laser Engraver Firmware-ORTUR laser master firmware, smarter, faster, higher precision and easier to use. Laser power range could be S0 - S1000, compared to 8Bits desktop laser engravers, which only has S0 - S255, ORTUR Laser Master could control laser beam more accurately, could even use the high power laser unit to "draw" a picture on paper, that the 8Bits high power laser engravers could not do. Engraving speed could be as high as 3000mm/Min. (If do not consider the laser carving result, the velocity of movement could be as high as 1000MM/S). We can not change your address and color once we've dispatched package and deliver to the shipper.

Communication always is best way to solve problem. We accept any return in 30 days that we promise. If item is defect or wrong when arrives. Please never return the parcel without agreement.

From us, it is no possible for us to get the parcel. We at strive to give all of our customers a 5 star service. As this helps us maintain a quality service.

Communication is very important, we believe we can resolve all the problem with you. It's our pleasure to answer any questions you have.